Wear protective gear like gloves and goggles throughout the hanging process to protect yourself from stray screws or power tools.Ensure stability by using screws that will fix securely into the wall and stay in place.Measure twice to make sure that the wall can support the weight of the item you want to hang. ![]() So to make sure you’re safe and secure, it’s important to follow some basic safety tips before you start. ![]() Hanging heavy items on lath and plaster walls is a tricky task done incorrectly, it can damage your walls and fixtures, or worse, put you at risk for injury. Now that you have everything you need, it’s time to get started! Safety Guidelines for Hanging Heavy Items You’ll also need wall anchors or toggle bolts, lag screws with washers for attaching lag shields to your wall, and toggle bolts for heavier items.įinally, don’t forget the basics: a hammer, screwdriver, and measuring tape will come in handy too. You’ll need a stud finder to locate the studs in your wall, as well as a drill with a masonry bit for making holes in your lath and plaster walls. Hanging heavy items on lath and plaster walls can involve a bit of extra work, but the results are worth it.īefore you start, you’ll need to make sure you have the right materials and hand tools for the job. Worst case you have a few extra holes behind your TV.8.3 What’s the best way to hang heavy objects on lath and plaster walls? Tools and Materials Needed to Hang Heavy Things on Lath and Plaster Walls Go vertically up using a level to keep plumb and pop a 3" screw in to see if you're on a stud. Then it should be 16" on centre to the left and right. If there's an outlet nearby, you can usually tell which side of the stud it's mounted to by opening it up and having a look. I'm sure the interwebs can tell you how to find a wall stud, but sometimes it's just trial and error. I've used small drywall anchors on our lathe/plaster walls most of which have a layer of drywall on top with good results for small things like a shelf, but naturally not a TV. If it hits resistance pull it out and drill a bit more as you likely didn't get through the lathe or the hole in the wood is too small for the anchor.Ģ - how do you find studs in a lathe/plaster wall and/or what sort of anchors would you use for a heavier object like a TV. Don't hog out the hole too much and pop the anchor in. Make sure you have some adjustability in the wire on the artwork - easier to tweak that than move a hanger 1/4"įor your artwork with two fixed mounting locations 22" apart, I assume it needs a screw into the wall protruding a little bit. Just be careful about hanging height measuring as 2 hangers spread 8 inches apart say will hang the artwork higher than a single hanger. Gives you more a more stable support for the picture. If your picture is large/heavy, use 2 hangers. As I mentioned, I will usually put a small piece of tape to help avoid cracking the plaster, but frankly I think that's pretty useless. They couldn't be more different when considering how to mount on a wall.ġ - can you use standard picture hangers in a lathe/plaster wall. I guess I don't need studs for my current project but was considering to mount a TV in the other room, figured it would be good practice.Ī TV and an oil painting are literally apples elephants. There's a large oil painting in storage that I was thinking about hanging as well, probably 15 lbs. last owners made a mess of the wall with spiderweb cracking of the plaster from the nails. I just pulled out a bunch of nails and patched the plaster. Maybe the picture hangers with a drywall screw like this: I'm buying a laser level and whatever stud/electrical finder is recommended.įramed prints are about 8 pounds each. ![]() wall is about 20ft long but sofa isn't centered due to the placement of the TV between a doorway and a large picture window.Īny info would be appreciated. So what would your advice be? I just painted and my walls have nothing on them. My entire wall's finished section is only about 4" thick so I'm basically hitting the other side with 2" hollow wall anchors. My first try was drilling into a hallway (backing into a closet) and the 2" molly bolts I bought (due to a YouTube) video and drilled into the lathe seemed too long. ![]() If I'm drilling into the lath, how do I locate the electrical?Īlso, do you center the artwork in the center of the wall or just over the couch (or to the eye)? Also, the artwork I bought has two hangers 22" apart, therefore, it doesn't look like I'll be using 2 studs anyway. Apparently it's harder to find the studs due to the wood lath in behind. I've read that plaster and lath walls are somewhat different in hanging things.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |